Kelly: /* SWITCH NAMES */

2021-10-23T19:36:00Z

‎SWITCH NAMES

Kelly: Created page with "===SWITCH NAMES=== (used with s, s1 and s0 commands for normal switches s0, s1, s2, etc. for rotary switches) This section describes the various switches in the EC-135 and the..."

2021-10-23T18:44:06Z

Created page with "===SWITCH NAMES=== (used with s, s1 and s0 commands for normal switches s0, s1, s2, etc. for rotary switches) This section describes the various switches in the EC-135 and the..."

New page

===SWITCH NAMES===
(used with s, s1 and s0 commands for normal switches s0, s1, s2, etc. for rotary switches) This section describes the various switches in the EC-135 and their functions. Push buttons (marked with [b]), and rotary knobs (marked with [r]) are also shown here. Switches that are for RP purposes only and do not have an effect on the helicopter are marked [RP] in the description. For switches that have guards, the guard is addressed by appending a "-g" to the switch name (marked with [-g] after the name in the table below).

====Electrical System====
Switch Description
batt Energizes DC primary buses from the main battery
gen1 Energizes #1 DC bus from generator on #1 engine
gen2 Energizes #2 DC bus from generator on #2 engine
inv Inverter. Energizes AC Bus from primary bus
shed[-g] Shed non-essential electrical systems.
tie1[-g] Ties battery to #1 primary bus when in NORM position
tie2[-g] Ties battery to #2 primary bus when in NORM position

====Fuel System====
Switch Description
prime1 Prime pump for for #1 engine
prime2 Prime pump for for #2 engine
xfer-f Forward fuel transfer pump. Feed both left and right tanks.
xfer-a Aft fuel transfer pump. Feed both left and right tanks.

====Engine Systems====
Switch Description
fadec1 FADEC #1
fadec2 FADEC #2
ec1-g Guard for #1 engine control
ec2-g Guard for #2 engine control
manStart1[-g] Engine #1 manual start (disabled and unauthorized)
manStart2[-g] Engine #2 manual start (disabled and unauthorized)
emode1[-g] Engine #1 manual/automatic mode selector
emode2[-g] Engine #2 manual/automatic mode selector
train[-g] Training mode (for simulalted one engine operation)
emoff1[-g][b] Engine #1 emergency fuel cut-off
emoff2[-g][b] Engine #2 emergency fuel cut-off

====Lighting====
Switch Description
pos Position lights
strobe Strobe lights
anticoll Anti-collision light
taxi Taxi light
ldg Landing light
inst Instrument lights on/off
instBrt Instrument light brightness
stbyhorlt Standby horizon light
cargo Cargo light

====System Test====
Switch Description
ext1 Engine #1 Fire Extinguisher Test
ext2 Engine #2 Fire Extinguisher Test
warnunit Warn Unit Test
syshyd System hydrulic warning test

====Avionics Systems====
Switch Description
avi1 Avionics Master #1
avi2 Avionics Master #2
stbyhor Standby Horizon Power

====Heating and Misc Systems====
Switch Description
pilotPitot Pilot side pitot heat [RP except alert light]
cpPitot Copilot side pitot heat [RP except alert light]
aircond Air conditioner [RP]
paxblw Passenger compartment blower [RP]
heat[r] Heater [RP]
vent[r] Vent [RP]
elt Emergency Locater Transmitter
wiper Windshield wipers [RP]

← Older revision		Revision as of 19:36, 23 October 2021
Line 68:		Line 68:
	elt Emergency Locater Transmitter		elt Emergency Locater Transmitter
	wiper Windshield wipers [RP]		wiper Windshield wipers [RP]
		+
		+	===CHAT COMMANDS===
		+
		+	====Autopilot====
		+
		+	{\|class=wikitable
		+	!Command
		+	!Description
		+	\|-
		+	\|ap IAS \|\|Toggle airspeed hold
		+
		+	\|-
		+	\|ap ALT \|\|Toggle altitude hold
		+	\|-
		+	\|ap HDG \|\|Toggle heading hold
		+	\|-
		+	\|ap V/S \|\|Toggle vertical speed hold
		+	\|-
		+	\|ap HVR \|\|Enter autohover mode
		+	\|-
		+	\|ap SEL \|\|Change "selected" parameter
		+	\|-
		+	\|ap + \|\|Increase value of selected parameter
		+	\|-
		+	\|ap - \|\|Decrease value of selected parameter
		+	\|-
		+	\|ap DIS \|\|Disconnect autopilot
		+	\|-
		+	\|ap IAS n \|\|Set the target airspeed to n
		+	\|-
		+	\|ap HDG n \|\|Set the target heading to n
		+	\|-
		+	\|ap L n \|\|Set the target heading left by n degrees
		+	\|-
		+	\|ap R n \|\|Set the target heading right by n degrees
		+	\|-
		+	\|ap ALT n \|\|Set the target altitude to n
		+	\|-
		+	\|ap V/S n \|\|Set the target vertical speed to n
		+	\|}

EC-135/Appendices - Revision history

Kelly: /* SWITCH NAMES */

Kelly: Created page with "===SWITCH NAMES=== (used with s, s1 and s0 commands for normal switches s0, s1, s2, etc. for rotary switches) This section describes the various switches in the EC-135 and the..."